Home :: Epoxy Tips

Epoxy Tips

Troubleshooting

Surface is wet or sticky in spots after rest of surface is cured.

See #3, #7 and #8


Surface is tacky after several days.

See #7, #8 and #9


Epoxy is cured but peels of surface easily.

See #10


Epoxy cures but is softer and more flexible than usual.

See #3, #7, #8 and #11


Epoxy cures in mixing bucket before you can apply it.

See #1a and #2

1a. Never mix more epoxy then you can apply within the pot-life printed on the label.
1b. Never apply product that is starting to "kick", "Gel" or is getting too hot.

2. Epoxies have shorter pot-life as the daily temperature rises. Increase of 10 degrees Fahrenheit above the average 77 degrees Fahrenheit will usually shorten the pot-life by 5 minutes. The longer the mixed product stays in the mixing bucket and the higher the amount of mixed product will dramatically shorten the pot-life if it stays in mixing bucket too long. After properly mixing try to apply/spread the product as fast as possible for more working time. Preparation is everything, applying most of our products usually does not take long.

3. Always mix the epoxy according to the proportions listed on the the containers, varying the amount of hardener is permissible on certain products but you should always stick to the recommended ratios.

4. If you don't know what you are doing, try a test spot or give us a call for any advice or check out the Epoxy Message Board.

5. In applying epoxy putties, the surface can be lubricated and smoothed by wetting the applicator spreader, a damp sponge or keeping yours hands wet with water. It will save you time in sanding and fairing.

6. Always wear gloves when handling epoxies. Some people are allergic to epoxy and it can cause a skin rash

7. Mixing is very important. When mixing epoxy , you should use what is called "Boxing Technique" Mix your 2 components together then pour into another container and mix again. Scraping the sides and bottom of the container is very important

8. Improperly mixed proportions or failing to mix thoroughly by scraping side of mixing container and bottom of container will cause soft or sticky cure.

9. Most epoxies can not be used below 60 degrees Fahrenheit.

10. Epoxy will not stick to dirty, oily, hard, shiny or flaking surfaces or pressure treated wood. Surface preparation is very important.

11. If you store unused epoxies for a long period of time, mix each can separately before combining the 2 parts together.

Because Fasco Epoxies Inc. cannot control how these products are used, it makes no warranties, either expressed or implied, as to the suitability or use of any product for any application. Fasco Epoxies, Inc. will not be held liable for incidental or consequential damage from such use.

Fasco Fillers & Additives

Fumed Sillica
1/4 Inch Chopped Fibers
Glass Bubbles
Talc Powder
Micro Balloons
Wood Flour
Graphite Powder

Fas-Grip Non-Skid

Non-Skid

Fast Stone #7

Fasco #7 Regular
Fasco #7 Underwater Paste

Steelflex Epoxy #9X

Fasco #9XC Clear Steelflex
Fasco #9XN Neutral Steelflex
Fasco #9XN 2000 Superslick
Fasco #9XS Super Steelflex
Fasco #9XW White Steelflex

Ultra Clear #23

Ultra Clear #23

Fas Fair #26

Fasco #26 Fairing Compound
Fasco #26 MEC Marble Compound

Fas Cast #34

Fasco #34 Casting Epoxy

Table Top #39

Fasco #39 Table Top Epoxy

Water Reducible #50WR

Fasco #50WR Water Reducible Epoxy
Fasco #50WR Color

Fasco #55

Fasco #55 Clock Epoxy
Fasco #55F Fishing Rod Epoxy

Fasco #88 Epoxo Paste

Fasco #88 Clear
Fasco #88 Regular
Fasco #88 Superflex

Fasco #88 Epoxo Liquid

Fasco #88 Epoxo Liquid

Fasco #99 Stop Rot

Fasco #99 Stop Rot

Fasco #103 LVX

Fasco #103 Laminating Epoxy

Fasco Pigments

Epoxy Pigments
Pearlescent Pigments

Fasco #110 Glue

Fasco #110 Glue
Fasco #110 Fast Set Glue

Gift certificates