• Now AcceptingPayPal
    0
7 Fas-Stone Epoxy Patching Compound

        7 Fas-Stone Epoxy Patching Compound

        SKU: 7P

        Fasco 7 Fas-Stone Epoxy Patching Compound

        Not rated yet
        0
        • $32.49
         
        In stock(127 items available)
        OR
        24 Pints per case
        12 Quarts per case
        4 Gallons per case
        Epoxy putty for repairing concrete metal, wood, fiberglass etc. Bonds new concrete to old.
        Thick white putty used on dry to damp surfaces and underwater.
         

        DESCRIPTION

        Fas-Stone 7 is a two-part paste mix which exhibits the following characteristics:

        1. Will cure to a hard, rock-like solid in the presence of dampness or even fully submerged under water.
        2. Excellent adhesion to concrete, aluminum, metal, wood, fiberglass, etc.
        3. Has great tensile strength and is an excellent epoxy glue.
        4. Has great impact resistance and chemical resistance.
        5. Can be drilled or tapped.
        6. Will set or gel in 3 hours. Rock hardness in 8-10 hours.
        7. Can be mixed with sand as much as 1:1, making an epoxy cement and cutting the cost in half.
        8. Can be troweled on as a floor-topping compound producing a floor surface of great durability and chemical resistance. When mixed with sand 1:1, coverage per gallon of the mixed material at 1/8" thickness is approximately 18 square feet.

        USES

        1. Low cost epoxy glue of great strength.
        2. Industrial floor topping for greater wear and chemical resistance.
        3. Underwater sealing and patching compound.
        4. Concrete walk, driveway, or floor patching compound. Will glue old concrete to new concrete.
        5. Many other applications where great gluing strength, fast set time, chemical resistance and impact resistance are needed.

        APPLICATION

        1. Mix equal parts of Part 1 and part 2 very thoroughly. As a concrete patching material, as much sand may be added as desired to reduce cost and increase viscosity. In general, mixes in excess of 1:1 will be too dry and not have proper adhesion.
        2. Surface to be repaired or glued should be as clean as possible and free of grease, wax or oil.
        3. Apply patching compound in any thickness desired. When troweling as a floor topping or wall surface, water may be used to wet the trowel and smooth off the surface.
        4. After mixing Part 1 and Part 2, material must be used within 1 to 1-1/2 hours, depending on size of batch mixed. Larger batches will gel quicker.
         

        APPROXIMATE PHYSICAL CHARACTERISTICS

         Pot Life'1', 1 lb. Mass @ 77°F.                30 Minutes

         Cured State Properties(2)

        Heat Deflection Temperature                   42°

        Tensile Strength                                       5000 PSI

        Compressive Strength                            10000 PSI

        Izod Impact. ft-Ib/inch notch                       1.02

        Hardness, Shore D                                     77

        Water, Absorption(4)                                    0.54

        Weight Loss(3)                                             0.81

        Electrical Properties

        Dielectric Constant(5)                           3.62

        Dissipation Factor (5)                           0.037

        Volume Resistivity, ohm-cm

        @ 25°C.                                          8.2 (1013)

        @ 66°C.                                          7.5 (109)

        @ 93°C.                                                 (109)

        1. Equal volume ratio.
        2. Determined on 1/8" thick test specimens at 25°C. Cured for 16 hours at 25° C. followed by 2 hours at 100°C.
        3. Percent weight loss after 24 hours at 150° C.
        4. Percent weight gained after 24 hours immersion in water at 25° C.                                              "
        5. Determined at 106 Hertz.
          • SKU
            7PK
          • Weight
            1.25 lbs
        • Mixing Ratio
          1:1
        • Select Each or Case
          Each, Case
        • Select Kit Size
          1 Pint Kit (1/2 Pint of Part 1 & 1/2 Pint of Part 2), 1 Quart Kit (Pint of Part 1 and Pint of Part 2), 1 Gallon Kit (1/2 Gallon of Part 1 & 1/2 Gallon of Part 2)
        Customer reviews
        There are no comments yet. Be the first to leave a comment
        Please sign in to add review
        To replace this text with your store's actual shipping info, go to "Design -> Menus & Pages -> Product Page Tabs" and edit the Shipping info page.

        We accept the following payment methods:

        Accepted payment methods

        To replace this text with your store's actual info on payment methods, go to "Design -> Menus & Pages -> Product Page Tabs" and edit the Payment methods page.

        This page is intended for your policy regarding returns and refunds.

        Here you can provide information as to what products can be returned, how many days your customers have to return their purchase, whether they will receive a refund in the original form of payment, a replacement or a store credit, who pays for the shipping of the previously purchased products to the store, and so on.

        To replace this text with your store's actual return policy, go to "Design -> Menus & Pages -> Product Page Tabs" and edit the Return Policy page.